Room Darkening Seclusions Single Cell Shades
Levolor Blinds

All Mounting Hardware Included!

Steel brackets snap into place, making shades very easy to install!

• • Size 1: 3/8” Projection (1 spacer)
  • Size 2: 1” – 3” Projection (adjustable)
• Hold Down Brackets: For outside mount only, available for securing the bottom rail in position. These brackets can stop a shade from bouncing and loosely swinging if the shade is hung on a door.
• Cord Cleats: Secures the cords to wall for child and pet safety.

Top Down/Bottom Up: The shade can be lowered from the top and raised from the bottom. Thus, the shade can be positioned anywhere in the window. Separate controls on each side of the shade control the rails independently. The shade is measured the same way as a standard shade.

Top Down Only: The fabric lowers from the top of the shade only. The bottom rail does not operate. Measure this shade as a standard shade.

Continuous Cord Loop System: A pulley system where the cord length is always the same. A simple pull on the control cord positions the shade at the exact height desired.

Cordless System: The elimination of lift cords make the shade child and pet safe. Simply raise and lower your shade by pushing down and pulling up on the bottom rail. The spring-motor activation offers easy operation. A handle is provided with every cordless shade.

Cordless Top Down/Bottom Up: Combine Levolor’s Cordless lift system with Top Down/Bottom Up engineering. This shade can be lowered from the top or raised from the bottom—you decide how much light control you want and where on the window the light control should be. The shade is measured in the same way as a standard shade and each shade is provided with a handle to raise and lower it.

Additional Special Options Not Provided on Website (Please call 1-800-548-5711 for pricing and details!)

• Day/Night Shades - (Transformations)
• Arches
• Half Arches
• Circles
• Hexagons
• Octagons
• Standard Skylights
• Fanned Angle Tops
• Fanned Angle Bottoms
• Cutouts

Energy Shield: Is an added layer that helps block air and provides additional insulation. In warmer months Energy Shield eliminates air flow through the shade and blocks interior cooled air from escaping your home. In colder months, Energy Shield eliminates air flow through the shade, provides additional insulation and allows warmth and filtered ligh from the sun.

Note: For width specification please know the following

                Inside Mount: Measure from the inside surface to the inside surface. Please provide us with exact measurements as the manufacturer will make the necessary deduction of 3/8” off of the fabric.

                Outside Mount: Measure the exact area you wish to cover as the manufacturer will produce your shade to your exact measurements. Be sure to take the window trim into account.

General Specifications (unless otherwise specified under certain specifications)

Installation Brackets

Quantity of Cords

Stacking Chart: This chart represents the amount of the shade that is gathered at the top of window when fully raised. The measurements in this chart includes the stack of the fabric, the headrail, and the bottomrail.

Standard Shade Specifications (This is for standard shade only, please see specifications for special options as they may be different than the standard shade availability)

Width: 6” – 120”

Height: 6” – 144”

Headrail Dimensions: 1.81”w x 0.52”h

Bottomrail Dimensions: 1.48”w x 0.43”h

Mounting Requirements

• Flush Mount: 2 ¼” Depth
• Mounting Depth for Standard: 5/8”

Top Down/Bottom Up

Width: 12” – 72”

Height: 6” – 96”

Top Down Only

Width: 12” – 72”

Height: 6” – 96”

Continuous Cord Loop System

Width: 18” – 120”

Height: 6” – 144”

• If width is greater than 120”, the maximum height is 96”
• If width is less than 30”, the maximum height is 96”
• This feature is not available with cordless, top down, top down/bottom up, day/night (Transformations) shades, angle top/bottom shades, or skylights.
• For 2 on 1 Headrail, controls will be located on the left side of the left shade, and the right side of the right shade.

Headrail Dimensions: 1.78”w x 1.35” h

Bottomrail Dimensions: 1.72”w x 0.58”h

Flush Mount Minimum Depth: 2 1/8”

Stacking Chart- Including Headrail and Bottomrail

Cord Loop Lengths

Cordless

Width: 10” – 120”

Height: 6” – 96”

• If height is greater than 84", minimum width is 14".

Headrail Dimensions: 1.78”w x 1.35” h

Bottomrail Dimensions: 1.72”w x 0.58”h

Flush Mount Minimum Depth: 2 1/8”

Stacking Chart- Including Headrail and Bottomrail

2-on-1 Headrail

Standard Shade

Width: 12” – 120”

Height: 6” – 144”

Cordless Shade

Width: 20” – 120”

Height: 6” – 96”

If the width is less than 30”, the maximum height is 76”

How to Measure for a 2-on-1 Headrail:

Outside Mount:

1. Overall Shade Width: Measure the desired width
   1. Levolor recommends that you add 3” to the overall width of the window for complete coverage. For maximum privacy, add an additional 3” to the total width of the window.
2. Left Shade Width: Measure the width that you want the left shade to cover
3. Right Shade Width: Measure the width that you want the right shade to cover
   1. The left shade width plus the gap, plus the right shade width must equal the overall shade width.
4. Height: Measure the desired height
   1. Levolor recommends that you add at least 3” to the height of the window for complete coverage. For maximum privacy, add an additional 3” to the total height of the window.
5. Order the left shade first (This is shade 1)
6. Note: There will be a ¼” innerspace between the fabric on the left and right shade to allow for shades to operate independently. This standard innerspace can be increased if customer requests, however the minimum is ¼”

Inside Mount:

1. Overall Shade Width: Measure the window’s width at the top, middle, and bottom. Order the narrowest measurement.
2. Left Shade Width: Measure the width that you want the left to cover.
3. Right Shade Width: Measure the width that you want the right to cover.
4. Height: Measure the window from the top to the bottom for desired height
5. Order the left shade first (This is shade 1)
6. Note: There will be a ¼” gap between the fabric on the left and right shade.